SHOP BY BRAND
Home » Martin Tools
Pages: 1 2 3 4 5 [Next >>]
Displaying 1 to 20 (of 98 products)
Ball Peen Hammers - 2 oz101G
3 in stock
The low crown face of the Slapping Spoon measures 9" long by 2-1/8" wide with a 6" long handle. This spoon works well for smoothing and shaping. Weighs about 2-1/2 lbs. Made in the USA. Limited Lifetime Manufacturer's Warranty.
Use to ding ridges smooth and level. When held against ridge and struck with hammer, spreads blow over large area making smooth job and preventing damage to metal or finish. Not made for prying. Length 10" overall. Face 2" x 4-5/16".
6 in stock
General purpose fender spoon. Used as dolly behind brackets, inner panels and similar places. Handle offset to give balance when dinging and for long reach. Has high-crown working surface. Face 1-3/4" × 5-1/2". Handle 1" octagon 4-3/4" long. Weight 3.0 lbs.
2 in stock
Long handle permits many uses in places otherwise inaccessible. Can be driven between reinforcements and outer panel, then used to pry outward as the metal is dinged. Excellent forming and caulking tool for the deep pockets of doors, quarter-panels, rear fenders and lower trunk panels. Size 2-1/2&qu... <more>
features and benefits: face 2" x 7" length 10-1/2" overall used to pry up dents behind curved reinforcements long curved spoonlong, thin, curved blade is handy for prying up dents behind curved reinforcements in header panels, hinge anchors in doors, body pillars and reinf... <more>
The answer to repair problems on high fins. A dolly, a spoon and a pry. Long handle and special contours for working up inside cramped fins. Wide spoon transmits hammer blows over wide area without damaging finish. 1" handle diameter. 19" overall length.
1 in stock
Designed for _at surfaces. All the features of a toe dolly. Sizes: 43_4_×21_4_×11_16_
Thinness and length provide easy accessibility to narrow pockets. Large, flat face is frequently used in shrinking and dinging flat panels. The flat sides furnish a convenient anvil for repairing flanges. Sizes 4-3/4" x 2-3/8" x 1-1/8".
Shaped like a toe dolly but has one face covered with raised serrations for shrinking metal stretched by dents.
4 in stock
Design makes it possible to reach easily into sharp corners and wide radius. These features are exclusive to the heel dolly and continue its high demand. Sizes 3-1/4" x 2-1/2" x 1-7/16".
Provides convenient and comfortable hand hold during heaviest blows. Weight, balance and several differently crowned working faces, together with (2) beading and flange lips, give this dolly broad general use. Sizes 2-7/8" x 2-3/8" x 2-1/4".
Excellent precision made wire caulking iron. Polished working surfaces are rounded for use on inside moldings. Face 1-3/4" × 1". Overall length 11". Weight 1.4 lbs.
These reels incorporate heavy gauge steel and corrosion resistant components to withstand the harsh conditions in the workplace. They can be wall, overhead, bench or vehicle mounted. Hose reel features: stainless steel construction dual axle support -a dual supported axle can withstand the constant ... <more>
features and benefits: length: 31" use twisting or prying action access dents inside doors or between inner/outer fenders with ease made in the usathis curved pick makes it easier for the hard to reach surfaces. curved to get to and work out the dents. Made with the strength a... <more>
Extremely short length. Curved and pointed. Use twisting or prying action. Length 12".
features and benefits: 15/16" opening; angle wrench made with a chrome finish 30 degree angle head thin pattern for the use on jam nuts and confined areas made in the usaservice wrenches are traditionally designed with trucks and hydraulics in mind. they are also very ... <more>
Features and Benefits: 1" opening; angle wrench Made with a Chrome finish 30 degree angle head Thin pattern for the use on jam nuts and confined areas Made in the USAService wrenches are traditionally designed with trucks and hydraulics in mind. They are also very usef... <more>
features and benefits: 1-1/8" opening; angle wrench made with a chrome finish 30 degree angle head thin pattern for the use on jam nuts and confined areas made in the usaservice wrenches are traditionally designed with trucks and hydraulics in mind. they are also very ... <more>
- products have enhanced descriptions, specifications, and/or images available
Beach Audio - RSS Feed for Martin Tools
Sales and Support
© 2014 Beach Audio, Inc. All Rights Reserved